MOXA VPort 464

The VPort 464 4-channel industrial video encoder uses the H.264 video compression algorithm to provide the best video quality on the market, but with a smaller bandwidth requirement than other video compression standards. In addition, to meet various requirements, each channel of the VPort 464 can support 2 video streams simultaneously or you can merge all 4 channels into 1 quad view stream using H.264 and MJPEG compression formats, providing greater flexibility for a variety of uses, including viewing, recording, and analysis. The rugged industrial design, which includes a -40 to 75°C operating temperature, IP30 protection, and industrial certifications, make the VPort 464 suitable for harsh environments.

The VPort 464 comes with two gigabit Ethernet ports and supports cascade mode and network redundancy. In addition, Moxa’s innovative DynaStream™ technology lets you change the video frame rate automatically, allowing you to control your network bandwidth budget and simplify network system management. The CBR Pro™ function guarantees the lowest packet loss for limited bandwidth transmissions to ensure that images will not exhibit the mosaic effect.

• Video
Video Compression	H.264 (MPEG4 part 10, AVC) or MJPEG
Video Inputs	4, BNC connector (1.0 Vpp, 75 ohm)
Video Output	Via Ethernet
Video Streams	Dual streams for each channel, or 1 quad stream
NTSC/PAL	Auto-sensing or manual
Video Viewing	• DynaStream™ support for changing the video frame rate automatically • On-screen display: Text lines, Graphical image (BMP, GIF, or JPEG) • CBR Pro™: Support for accurate streaming bit rate control • Maximum of 5 simultaneous unicast connections, and 50 multicast clients • Image tuning to control brightness, contrast, saturation, hue, sharpness, and noise reduction
• Audio
Audio Inputs	1, Line-in 3.5 mm phone jack connector
Audio Outputs	1, Line-out 3.5 mm phone jack connector
Audio Format	Mono, PCM (G.711)
• Network
Protocols	IPv4/v6, TCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, UPnP, RTP, RTSP, ICMP, IGMPv3, QoS (ToS), SNMP V3, DDNS, Modbus/TCP, 802.1X, SSH/HTTPS, NTCIP
Ethernet	2 10/100/1000BaseT(X) Ethernet ports, RJ45 connectors
• Serial Port
PTZ Ports	1 RS-232 or RS-422/485 port, terminal block connector or DB9 male connector, 115.2 kbps
Console Port	1, RS-232 RJ45 port
• GPIO
Digital Inputs	4, max. 8 mAHigh: +13 V to +30 V; Low: -30 V to +3 V
Relay Outputs	2, max. 24 VDC @ 1 A
• LED Indicators
STAT	System status
PWR1	Power 1
PWR2	Power 2
FAULT	Can be configured to correspond to system alarm, power failure, or disconnected network
PTZ	Indicates if PTZ or COM port data is being transmitted
SD	Indicates if microSD card mounting or unmounting is successful
V1, V2, V3, V4	Video input signal activity for channels 1 to 4
• Power Requirements
Input Voltage	2 redundant power inputs, 12 to 32 VDC or 18 to 30 VAC, terminal block connector
Input Current	12 to 32 VDC, 1.0 A (max.) or 18 to 30 VAC, 1.0 A (max.)
Power Consumption	12 W (max.)
• Physical Characteristics
Housing	Metal, IP30 protection
Dimensions	80.2 x 135 x 105 mm (3.16 x 5.31 x 4.13 in)
Weight	1.13 kg (2.49 lb)
Installation	DIN-rail mounting (standard), wall mounting (optional)
• Alarms
Video Motion Detection	Each channel has 3 independently configurable motion areas
Intelligent Video Surveillance	Camera tampering detection
Scheduling	Daily repeat timing schedule
Imaging	JPEG snapshots for pre/trigger/post alarm images
Custom Alarms	HTTP event servers and CGI events for setting customized alarm actions
Email/FTP Messaging	Automatic transfer of stored images via email or FTP with event-triggered actions
• PTZ (Pan/Tilt/Zoom)
PTZ Camera Control	Via RS-232/422/485 PTZ port
PTZ Control Functions	Pan, tilt, zoom, focus, moving speed, preset position (max. 128 positions)
PTZ Function Updates	Driver upload supported
Supported Device Protocols	Pelco D, Pelco P, Custom Camera
• Security
Password	User level password protection
Filtering	By IP address
Authentication	802.1X
Encryption	HTTPS, SSH
• Environmental Limits
Operating Temperature	Standard Models: -25 to 60°C (-13 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature	-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity	5 to 95% (non-condensing)
Vibration	IEC 60068-2-6, 2 to 13.2 Hz: 2 mm (peak-peak); 13.2 to 100 Hz: 0.7g; 1.50 hrs/axis IEC 60068-2-6, 3 to 9 Hz: 7 mm (peak-peak); 9 to 150 Hz: 1.0g; 1.86 hrs/axis
Shock	IEC 60068-2-27, 20g/11ms
Altitude	2000 m
Ingress Protection	IEC 60529, IP30
• Standards and Certifications
Safety	UL 60950-1
EMI	CISPR 22, FCC Part 15B Class A
EMS	EC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV IEC 61000-4-6 CS: 10 V IEC 61000-4-8
• MTBF (mean time between failures)
Time	569,152 hrs
Standard	Telcordia SR332
• Warranty
Warranty Period	5 years
Details	See www.moxa.com/warranty
• Minimum Viewing System Requirements
CPU	Intel Core i5, 2.4 GHz or above
Memory	1 GB memory or above
OS	Windows 7
Browser	Internet Explorer 9.x or above
• Software Development
VPort SDK PLUS	Includes CGI commands, ActiveX Control, and API library for customized applications or system integration for third-party developers (the latest version of SDK is available for download from Moxa’s website).
Standards	ONVIF, Profile S

ORDERING INFORMATION
Available Models
VPort 464	4-channel industrial video encoder, 2 10/100/1000 BaseT(X) Ethernet ports, -25 to 60°C operating temperature
VPort 464-T	4-channel industrial video encoder, 2 10/100/1000 BaseT(X) Ethernet ports, -40 to 75°C operating temperature
Optional Accessories • DIN Rail Power Supplies
MDR-40-24	40W/1.7A DIN-Rail 24 VDC power supply with universal 85 to 264 VAC or 120-370 VDC input , -20 to 70°C operating temperature
MDR-60-24	60W/2.5A DIN-Rail 24 VDC power supply with universal 85 to 264 VAC or 120-370 VDC input, -20 to 70°C operating temperature
• IP Surveillance Software
SoftNVR-IA	64-channel IP video surveillance software designed for industrial automation systems
• Other Accessories
DR-4524/75-24/120-24	45/75/120 W DIN-Rail 24 VDC power supplies
• Mounting Kits
WK-46	Wall Mounting Kit
RK-4U	4U-high 19" rack mounting kit